Maxcan told you how to maintain the print head of uv flatbed printer in the Winter.

我们建议在UV平板打印机使用的房间最好是有暖气或者空间，能很好的调节空间温度，保持一个恒温那是最理想的，长期的冷热交替更容易让设备损坏或者减少寿命，让UV平板打印机有一个好的工作环境，可以减少故障、降低维护成本。

 The weather is getting colder and colder. the wide  range of temperature will be lower than 1 degree Celsius.As you know,the ink is liquid, so as to prevent frozen cause damage to  print head.We suggest that it will be better to adjust the room temperature and it will be most ideal to keep a constant temperature if you use the UV flatbed printers in the room with heating or space. long-term cold and hot alternating it damages or reduces the service life of machines,.Please give the UV flatbed printers a good working environment to reduce fault and maintenance cost.

　　第一：每个客户冬天使用万能平板打印机，都可以用热风筒每天早上开机时候吹吹，这是在没有保暖措施的情况下。有条件的请开启空调，机器在使用前，请预热10-20分钟，以利于喷头保养。

First,Please keep the indoor temperature of 25 degrees Celsius or  so.And please check the status of ink before opening the machine. It will  be better for maintain the print head if preheating 10 to 20 minutes  ahead of schedule.Please replace to the antifreeze  if you use tap water in  the UV light tank.Confirmation the state of the liquid  before starting. And  please boot normally use after confirmed that it is ok.

　　第二：和夏季相比，冬季空气干燥，是万能打印机的“病情高发期”，如果不小心维护，可能会造成打印喷头堵塞，墨车异常（通常所说的撞头），严重的甚至因此而使喷头撞裂，一旦出现此类故障，那就要花上一笔不小的费用了，因此加强维护才是“治标治本”的良方！

Second,compare to summer. The air is dry in winnter,and it is the  illness season of uv flatbed printer. If you are not care for maintain , it may come about nozzles jam,carriage abnormal,even make the nozzle crack.Once appear this kind of failure, that is about to spend a lot of cost. Therefore strengthen maintaining is effective prescription of "appropriate measures ".

　　第三：由于天气比较寒冷，如果室内（工作环境）相对比较冷而且过于干燥的话，则要注意在平时摆放时，最好能将一块较大较厚的布罩在万能打印机上，特别是将进纸口及出纸口等全部盖住，因为喷头在打印机内，如果能保证冷空气不过多进入打印机内空间的话，则可防止打印喷头上的墨滴凝固，否则很容易引起堵头，造成打印效果下降。

Third,Due to the weather is so cold, if indoor (work environment) is relatively cold and too dry , It will be best to  cover a large thick piece of cloth on the universal printer at ordinary times. Specially covering all the into the mouth and out of the mouth  of the paper.Because the print head is in the printer,it can prevent the drops on the print heads solidification if we can ensure that the cold air move into the space of the printer.Otherwise it is easy to cause the plug and the loss of printing effect.

　　第四：如果长时间不用，还要注意的是每周最少开机一次，平板打印机在开机时需要预热并且会自动进行喷头清洗程序（通常开机清洗所消耗的墨水量很小），它可以将原来附着在喷头上的墨滴排出，避免因长时间墨滴停留于喷头上而造成堵塞。并且进行一次喷嘴检查，能有效地检查出目前喷嘴的使用情况，看是否有打印缺线等现象（通常打印缺线现象都是堵头的表现）。

Fourth,Please pay attention to open the machine on at least once a week if no use the machine in a long time.Flatbed printer  need to preheat when in the boot and nozzle cleaning program automatically(Usually boot cleaning water consumed of ink is very small).It can put out the  drops which be attached on the nozzle, to avoid the drops to stay for a long time on the nozzle and cause plugging plug.And do a nozzle check, which can effectively detect the usage of the nozzle, look to whether have the printing phenomenon such as lack of line.

Print head is so precious that please  take good maintenance.

Please contact me if you need more information.

Email: luocong@maxcan.cn

Whatsapp: +86  188 2653 9185

Skype:maxcan_Ann

Listing information:
Maxcan China
Room 805, Building No.6, Hengfeng Industrial park, Xixiang, Bao’an District, Shenzhen, P.R.China
Tel: 0755-29160974  0755-29169143
Fax: 0755-89485376
Email: sales@maxcanprinter.com
Web: www.maxcan.cn

Long press qr code scanning identification, pay attention to us, every day to different journey