The Ten behaviors of damaging to the print head of uv flatbed printer.

1、在未关闭电源开关和切断总电源的情况下随意安装拆卸UV平板打印机的电路。这种行为会损害各个系统的使用寿命，危害喷头。      
 1,  Random removing the electrical installation Lk of UV flatbed printers under the condition of not shutting off the power switch,or cutting off the total power . This behavior will damage the service life of the system and harm print head.

2、随意加注不同批次的墨水，或使用质量不过关的墨水或者清洗液。两种不同配置的墨水混杂会改变墨水色彩和品质，质量不过关的墨水会影响喷绘效果和堵塞喷头，质量不过关的清洗液可能会腐蚀喷头。    
 2, Random charging different kind of ink, or use the ink or cleaning liquid which the quality closes nevertheless. Two different Configuration ink hybrid will change the ink color and ink quality, quality will affect the print effect and block the ink nozzle.And the print head may be corrosion if using the cleaning liquid which the quality closes nevertheless

3、对喷头进行高压气枪大力清洗。喷头如果被轻微堵塞，建议使用吸尘器将灰尘洗出，再进行细致清洗，不要用这种方式。    
 3, Using high pressure air gun cleaning energetically the nozzle.  If nozzle just be blocked  slightly, it is recommended to use a vacuum cleaner to ashes dust wash out, then a detailed cleaning, do not use this way.

4、将喷头整个放入清洗液中浸泡。清洗液具有一定腐蚀性，所以一般只取适量导入喷头中进行清洗。    
4, Soaking the whole print head in the cleaning liquid. Cleaning liquid has some corrosive, so generally only Import appropriate cleaning liquid into the nozzle for cleaning.

5、将清洗液留在喷头中超过2天2夜。清洗液长时间浸泡可更有效清除污渍，但是，如果时间超过48小时，会对喷头喷孔造成影响。    
 5, Keeping the cleaning liquid in the print head for more than 2 whole days.  Soak with cleaning liquid for a long time can be more effectively remove stains. But it will harm for the nozzles if more than 48 hours.

6、用自备无质检产品清洁喷头。喷头十分容易被污染和磨损，所以请使用厂家指定产品和质检过关产品清洁喷头。    
6,Cleaning print head by no quality products. Print head is very easy to be polluted and wear. So please use the product which is factory Specify product and passed quality inspection to clean print head.

7、使用外力不规范调整喷头位置。无论是更换还是微调喷头，都不要使用蛮力，请按照规范谨慎对待喷头。    
 7, Use external force to adjust the location of print head. Whether replace or fine-tuning print head, don't use brute force. Please treat the print head with caution according to the specification.

8、清洗时不注意保护电路板和其他内部系统。清洗时请关闭电源，并且注意不要让水碰到电路板和其他内部系统。    
 8 ,No paying attention to protect circuit boards and other internal systems when cleaning. Please shut off the power, and pay attention to let the water far away the circuit boards and other internal systems when cleaning .

9、长时间使用超声波清洗机清洁喷头。其实，如果平时注意喷头保养的话，根本无需进行超声波清洗。超声波会对喷头造成不良影响。但是如果堵塞严重，需要使用超声波清洗的话，一次清洗时间最多为3分钟。如果一次没有清洗感觉，请等待喷头自然降温至正常状态后再进行第二次清洗。    
 9, Using ultrasonic cleaning machine to clean the print head for long time . In fact, There is no need to ultrasonic cleaning  if notice at ordinary times print head maintenance. Ultrasound can cause bad influence of print head. But if the congestion is serious, You need to use ultrasonic cleaning. A cleaning time up to 3 minutes. If  feeling not clean after one time cleaning, please after waitting for natural cooling to normal condition to reentry the second time cleaning.

10、不注意地线设备安全。UV平板打印机印刷受静电影响很大，所以必须经常地线设备连接情况，定期给地线周围洒一点盐水。
10 ,No paying attention to the safety of ground. UV flatbed printers print is highly affected by the static electricity.So regularly sprinkle a little salt water around ground wire when it is connected.

Please contact me if you need more information.

Email: luocong@maxcan.cn

Whatsapp: +86 188 2653 9185

Skype:maxcan_Ann

Listing information:
Maxcan China
Room 805, Building No.6, Hengfeng Industrial park, Xixiang, Bao’an District, Shenzhen, P.R.China
Tel: 0755-29160974  0755-29169143
Fax: 0755-89485376
Email: sales@maxcanprinter.com
Web: www.maxcan.cn